| PCE-PH 16 | |
| Measuring range | 0.00 ... 14.00 pH |
| Measurement accuracy | ± 0.1 pH (at 20°C / 68°F), ± 0.2 pH |
| Reading | 0.01 pH |
| Adjustment | Manual one-point adjustment |
| Power | 3 x 1.5 V (battery LR44 AG-13) |
| Operating conditions | 0 ... 50°C / 32 ... 122 °F |
| Dimensions | 175 x 51 x 25 mm / 6.9 x 2 x 1 in |
| Weight | Approximately 57 g / < 1 lb |
| PCE-TUM 20 | |
| Measuring range | 0.00 to 50.0 NTU and 50 to 1000 NTU |
| Reading | 0.01 and 1 NTU |
| Accuracy | ± 5% of the measured value or ± 0.5 NTU |
| Light source | LED, infrared at 850 nm |
| Lifetime | Almost unlimited |
| Light detector | Photodiode |
| Measurement time | < 10 s |
| Battery | 6 AAA batteries 1.5 V |
| Environmental conditions | Maximum 50°C / 122°F, maximum 85% RH |
| Dimensions (HxWxD) | 155 x 76 x 62 mm / 6.1 x 2.8 x 2.4 in |
| Weight | 320 g / < 1 lb |
| PCE-CM 41 | |
| EC conductivity measuring range | 0 ... 2000 µS / cm, 0 ... 20 mS / cm |
| EC conductivity reading | 1 μS/cm, 0.01 mS/cm |
| EC conductivity accuracy | ± 1% of the measuring range |
| Measuring range for TDS salinity | 0 ... 2000 mg / l (ppm), 20000 mg / l (ppm) |
| TDS salinity reading | 1 ppm (< 1320 ppm), 10 ppm (> 1320 ppm) |
| TDS salinity accuracy | ± 3% of the measuring range |
| Temperature measurement range | 0 ... 60°C / 32 ... 140 °F |
| Temperature reading | 0.1°C / 0.18 °F |
| Temperature accuracy | ± 0.8°C / 1.5 °F |
| TDS | 1 ppm (< 1320 ppm) 10 ppm (> 1320 ppm) |
| Calibration | 1413 μS / cm |
| Environmental conditions | 0 ... 60°C / 32 ... 140 °F, < 80% rh |
| Power | 4 x 1.5V AAA batteries (incl.) |
| Dimension | 186 x 40 mm / 7.3 x 1.6 in (HxW) |
| Weight | 130 g / < 1 lb |
Pool water pH meter kit PCE-PH 16-TUM 20-CM 41-KIT
/ Turbidimeter / Conductivity meter / Easy operation of various parameters
/ Turbidimeter / Conductivity meter / Easy operation of various parameters
The PCE-pH 16 meter is . If you do not regularly check the pH value with the pool pH meter, damage may occur to fittings and other metal materials. An insufficient pH value also reduces the effectiveness of the pool's chemicals.
Using the pH meter makes determining the pH value particularly easy. With an accuracy of ± 0.1 pH and a reading of 0.01 pH, reliable and precise measurements are obtained. To perform a measurement, the protective cover of the electrode must be removed. The electrode should be thoroughly cleaned before use with a neutral pH liquid. After cleaning the electrode, the meter is ready for use. The user should immerse the electrode in water and then, within a few seconds, the measured value is clearly displayed on the instrument's screen. The data hold function allows the storage of measured values. To keep the measured value on the display, simply press the "Hold" button. The manufacturer recommends cleaning the pH meter electrode with a neutral pH liquid after each measurement. The user has the option to switch electrodes and recalibrate them.
To ensure accurate results in the long term, the meter should be calibrated at regular intervals. The meter can be manually adjusted at any time easily and quickly, provided the measurement electrode is immersed in pH 7 solution. When the value stabilizes, the correct measured value can be adjusted via the calibration screw at the top of the display using the supplied screwdriver. Subsequently, the user can check the calibration using other solutions (e.g. pH 4 and pH 10).
Applications of pool pH meter
The pool water pH meter is the ideal water quality control instrument providing accurate and reliable measurements. Unstable pH levels disrupt the pool water balance, cause skin and eye irritation, and cause damage to the pool mechanisms and components. The meter operates on battery. Thanks to its compact and robust design, the meter is ideal for portable use.
Equipment
To ensure high measurement accuracy, the pH meter should be regularly calibrated with the calibration solution provided in the package (pH 4.01 and pH 7.01). For proper maintenance, the electrode should be regularly cleaned with the cleaning solution, ideally after each use.Portable turbidity meter according to ISO 7027 (with two measurement ranges with automatic switching from 0 ... 50 NTU and 50 ... 1000 NTU)
The PCE-TUM 20 is a portable handheld turbidimeter for analyzing water quality. The turbidity meter features two measurement ranges with automatic switching between 0 ... 50 NTU and 50 ... 1000 NTU for greater accuracy. For the lower turbidity measurement range, diffuse light or Nephelometry measurement methods are used. For the higher measurement range, an additional photodiode is placed on the opposite side. Using the included calibration solutions 0 NTU and 100 NTU, the meter can be adjusted and calibrated at any time. (Note: NTU means Nephelometric Turbidity Unit). An LED is used as the light source, operating at a wavelength of 830 nm in the infrared light spectrum and is therefore invisible to the human eye. Since the measurement is performed in the non-visible range, any coloring of the sample plays a very minor role in the measurement. With the arrangement of photodiodes at angles of 180° and 90°, the measurement of emitted light is used for the high measurement range and the measurement of scattered light for the low range. The PCE-TUM 20 turbidity meter meets all standards required by EN 27027 / ISO 7027.
Conductivity and salinity tester for EC and TDS (total dissolved salts or solids)
The PCE-CM 41 measures conductivity, the amount of total solid material or dissolved salts (TDS - Total Dissolved Solids), and temperature. It is an easy-to-use portable water quality meter, whose waterproof housing according to IP 67 fully protects the enclosed electronic circuits. The measurement of EC conductivity and TDS has automatic temperature compensation.
- Small and easy-to-use measuring device
- Ideal for portable use
- Replaceable electrode via BNC connection
- 3 x 1.5 V (battery LR44 AG-13)
- Accuracy ± 0.1 pH
PCE-TUM 20
- Large LCD screen 41 mm x 34 mm
- Real-time clock
- High accuracy
- Compatible with ISO 7027
- Infrared - Turbidity measurement method
- Measurement of scattered and transmitted light
- Data Hold
- Maximum and minimum value hold
- Calibration at 0 NTU and 100 NTU
- Compact, shock-resistant housing
- Automatic shut-off (after 5 minutes of inactivity)
PCE-CM 41
- Two ranges for high accuracy
- Measures conductivity / TDS value and temperature (3 functions in one device)
- Option to select TDS factor
- Automatic calibration: saves time and provides high accuracy
- Automatic shutdown
- Temperature display in °C / °F
- Waterproof (IP 67)
Package contents
1 x PCE-PH 16-TUM 20-CM 41-KIT
1 x PCE-TUM 20 turbidimeter
1 x PCE-CM 41 conductivity meter
1 x screwdriver
1 x 0 NTU calibration standard
1 x 100 NTU calibration standard
2 x Cuvettes
1 x Cleaning solution
1 x Cleaning cloth
3 x 1.5V LR44 AG-13 batteries
6 x 1.5V AAA batteries
4 x 1.5V AAA batteries
1 x Carrying case
1 x User manual
1 x PCE-TUM 20 turbidimeter
1 x PCE-CM 41 conductivity meter
1 x screwdriver
1 x 0 NTU calibration standard
1 x 100 NTU calibration standard
2 x Cuvettes
1 x Cleaning solution
1 x Cleaning cloth
3 x 1.5V LR44 AG-13 batteries
6 x 1.5V AAA batteries
4 x 1.5V AAA batteries
1 x Carrying case
1 x User manual
IP Protection
IPXY
-
X = Protection against solid objects & access to hazardous parts
-
Y = Protection against water ingress
| Value | 1st Digit – Solids / Access | 2nd Digit – Water |
|---|---|---|
| 0 | No protection | No protection |
| 1 | Protection against solids ≥50 mm (test probe Ø50 mm) | Vertical falling drops |
| 2 | Protection against solids ≥12.5 mm (test probe Ø12.5 mm) | Drops with tilt up to 15° |
| 3 | Protection against solids ≥2.5 mm (test probe Ø2.5 mm) | Spraying up to 60° |
| 4 | Protection against solids ≥1 mm (test probe Ø1 mm) | Splashing from all directions |
| 5 | Protection against dust (limited ingress without harmful effects) | Water jets (nozzle 6.3 mm) |
| 6 | Complete dust-tightness (dust-tight) | Powerful water jets (nozzle 12.5 mm) |
| 7 | — | Temporary immersion (usually 1 m / 30 min) |
| 8 | — | Continuous immersion (depth & time specified by manufacturer) |
| 9 / 9K | — | High-pressure & high-temperature water jets |
| Code | Availability | Price excl. VAT | Cart |
|---|---|---|---|
| PCE-PH 16-TUM 20-CM 41-KIT | On Order |
€810,00
|